what to do with ugly fans in house
Learn how to easily embrace a popcorn ceiling using classic Armstrong® WoodHaven Ceiling Planks with Easy Up® tracks and clips. No need to scrape the ceiling first! The pre-finished planks tin can be installed correct over popcorn ceilings.
Disclosure: I partnered with Armstrong Ceilings to encompass upward the popcorn ceilings in ii rooms in my house. All words, photos, ideas and opinions are my own.
The guest room times 2 update project that I have been mentioning in a few posts is completed. :-)
I know you lot are wondering what we have been up to that required usa to remove all the piece of furniture in the rooms equally we worked in each.
We chose to exercise the two rooms at the same time since both are visible when yous are standing in the foyer. I wanted both to look the aforementioned. It is hard to show in a photograph, but if you are continuing in the foyer, you lot look right at the popcorn ceilings in these two invitee bedrooms.
A few readers idea we must exist calculation new flooring, but that is not what we did.
I was very happy with how I decorated these rooms. It was the popcorn ceilings that I wanted to remove.
If you have older popcorn ceilings in your home and so yous know they collect dust and expect dirty after fourth dimension. To make matters worse they cannot be easily cleaned without the popcorn raining downwards into the room.
It was time to say goodbye.
What nosotros did was not remove information technology, only comprehend information technology. It was like laying a new wood plank floor, but in contrary – on a ceiling using Armstrong WoodHaven Ceiling Planks.
Covering a Popcorn Ceiling With Pre-Fabricated and Painted Ceiling Planks
When it comes to removing popcorn ceilings, I tried the budget-friendly water and scraping removal method when I made over the guest bath a few years ago. The method works, merely is extremely messy and I did betrayal a very uneven ceiling. For the guest rooms, I didn't want to become this road to find uneven or damaged ceilings underneath the popcorn.
Unless you are certain nearly the land of the ceiling that is under the popcorn layer, you may be opening a can of worms every bit one contractor told me, specially in older homes.
The popcorn could be hiding a multitude of sins – water damage, an uneven surface and more.
1 reason popcorn ceilings are used in homes is that they are an inexpensive way to hide imperfections, cracks, and marks. Since the 3-dimensional texture is fibroid and casts shadows, information technology tin disguise or even completely cover those older, shoddy repair jobs and natural aging. No one would ever know until you try to restore the original smooth finish.
This is clearly the example in my firm. We were far better off covering the popcorn ceiling rather than removing it.
That is what we did to update the two guest room ceilings… we covered the popcorn up.
It looks beautiful – classic and cottage-y. I honey it.
Armstrong Ceilings offers an Easy Upwards® rails and clip system which makes installing beautiful ceiling planks over your existing popcorn ceilings very doable. We chose the shine painted white planks, only there are many color and woods texture options bachelor.
If you want to no longer see these dated ceilings in your home, or just desire to add classic character to whatever room, then continue reading to see how Ed and I installed this Easy Upwards system in our guest rooms. It was far easier than nosotros thought.
WoodHaven Ceiling Planks with Piece of cake Up Rail and Clip Installation TIPS:
Ed and I are DIY'ers simply we're not at the aforementioned level as the pros you meet on habitation improvement shows. Nosotros definitely don't have all of the cool contractor tools you see being used on HGTV, but institute a few ways that made installing the ceiling planks easy for us.
When we decided to use the WoodHaven ceiling planks to cover the popcorn ceiling, we did some research online and also read all of the instructions included with each box of the planks.
What helped us the about though was watching forest working pro Ron Hazelton's video a few times where he shows how to attach the planks over a sheetrock ceiling.
We as well watched the installation video on Armstrong's website. With the Installation Instructions booklet that came with the planks and the videos, we were confident we could install the planks without any problems.
Once we started the projection, it was far easier than nosotros thought.
The hardest part of the entire project for both rooms was cutting the crown molding corner joints after the ceiling planks were installed. Thank goodness for caulk. :-) Installing the planks was then like shooting fish in a barrel compared to cutting crown molding corner joints.
The Easy Upward Organisation
The Like shooting fish in a barrel Up System is made upward metal tracks and clips. The ceiling planks are medium density fiberboard planks made to go over drywall, plaster, joists or even driblet ceiling grid.
You start installation past attaching the metallic tracks to the ceiling joists using 2.5″ forest screws. And then you adhere metal clips to each track. You could merely exercise i clip per rails, attach the plank, then repeat.
We found it easier to attach 3-4 clips per track at a time so you could focus on installing the planks. Our planks were 5″ wide so 3-4 clips worked well to continue everything in the same full general area.
The final footstep is to install the planks, inserting the tongue into the groove of the previously installed planks, and so securing the adjacent prune into the groove of the new plank.
- WoodHaven Planks are pre-finished. No need for staining or painting.
- When the ceiling is installed, it only lowers the ceiling height by approx. i- inch.
How To Install WoodHaven Planks Using Easy Upward® Tracks and Clips
- Read the Installation Instruction Booklet that comes with the planks throughly. (Armstrong recommends going online to read the virtually upwards-to-engagement installation instructions) and lookout the Ron Hazelton video so y'all sympathize the process in advance.
- With the popcorn texture on the ceiling, we found it difficult to become a expert reading of where the joists were using a stud finder. Since the ceiling is going to be covered, don't be afraid to drill a few holes in the ceiling to ostend the joist location.
- When cutting your plank pieces, practice not to use planks that are less than 26 inches in length to ensure that planks are attached to the rails with at least two clips.
- The screws that come with the planks were designed for installing the track directly to furring strips. Since nosotros were going through a layer of popcorn and sheetrock, we bought 2-i/2″ long forest screws.
- Use the cardboard from one of the boxes in which the planks came to make a template, if needed, for installing the planks effectually light fixtures and other ceiling penetrations. You lot may also need to purchase longer screws when you reinstall those ceiling fixtures.
supplies needed:
- Armstrong WoodHaven Ceiling Planks in Painted White: Item # 1148B – The planks come 10 planks to a box that covers 29 square anxiety.
- Round saw
- Miter saw
- Jig saw (for cutting planks around light/ceiling fan fixture
- Drill and drill bit slightly smaller than the size of wood screws
- Wood screws – nosotros used Power Pro Interior Wood Screws 9 x ii-1/2″
- Long level
- Chalk line
- Stud finder
- Tape measure
- Prophylactic mallet
- Dust mask
- Rubber glasses
- Wood shims
- Painter'south tape
- Pencil
- Bit piece of paper-thin from plank box
- Crown molding – enough to go around the perimeter of the room / finishing nails /recessed nail punch / hammer
- Semi-gloss paint for crown molding. I used SW Pure White #7005
- SPACKLE and sandpaper to cover nail holes on crown molding
Footstep ane: Measure the Square Footage of Ceiling
Using a measuring tape, mensurate the width and length of the room, to make up one's mind how many boxes of WoodHaven planks you will demand. Order a little fleck more than square footage than needed simply in example you make a wrong cut.
Step 2: Detect and Marking the Ceiling Joists
Using a stud finder, locate the ceiling joists and mark the joists with a chalk line. (If installing the ceiling planks past yourself run across the end of this post for tips on how to practise this successfully.)
Find the studs in the wall and mark with painter's tape. This volition help y'all when it is fourth dimension to adhere the crown molding where the wall meets the ceiling.
Step iii: Screw Metal Tracks into Ceiling
In one case your ceiling is marked with chalk lines yous tin install your get-go runway.
The beginning runway should be attached two″ from the wall. Subsequent tracks should be spaced at 16-24″ intervals. If you need more than i track to span the ceiling, attach the 2nd runway at to the lowest degree 1/8″ away from the first so in that location is room for the clips to slide dorsum and forth. Y'all should have a 1″ overlap where the commencement track in the line meets the second.
Your tracks volition run perpendicular to your joists meaning they will intersect with the chalk lines you snapped.
Be sure that your tracks exercise not cross over your light fixture holes.
If necessary, suit your tracks past reducing space between them to avoid having a infinite greater than 24 inches between tracks.
Unless the track length is the same length as your ceiling, you will need to make cuts. The tracks can exist cut with a hacksaw, sabersaw or snips.
Nosotros added a few cut tracks around the light fixture and air duct.
- Use a long bubble level beyond each track to brand sure information technology is level. If not, loosen screws and identify shims behind the tracks where needed in society to level each track.
Step iv: How Wide Should the Starting Plank Be?
Once all the tracks are upwards, you have to effigy out the width of the room perimeter planks and then the planks will fit across the entire ceiling. You'll desire to place the least seen "thinner" planks on ane border of the room, and have the middle be full width planks.
How wide should that starting plank be? There is a formula in the instructions that y'all'll need to follow to effigy out that measurement for your space. Only follow the formula to figure out how wide it needs to be. I've also included the adding below. Ed says to merely have it a pace at a time without too much assay and it volition work out perfectly.
- Measure out the length of the room (in aforementioned direction as the individual tracks accept been installed).
- Split the length in inches by 5
- Multiply the remainder by 5
- Add 5 to the total and separate by ii to become the desired width of the first and concluding row of planks.
- Sample:
- Let'due south say your room is 11′ (132″)
- 132/5 = 26.4 (.4 is the residual)
- .four*five = 2
- (2+v)/two = 3.five″
Step 5: Cut Tongue Side Off of Showtime Edge Plank
Cut the tongue side off of your first border plank.
The border wall planks are the get-go and last planks installed on your starting and finishing walls. In one case your border planks are cut to size, install them one/2 inch away from the wall, leaving 3/iv″ gaps at the ends to allow for woods expansion.
- Utilise 1 screw as pictured above to concur the border lath in place. The spiral will be covered by crown molding afterward on.
- But the border planks volition need screws.
Side by side, attach a clip to each track and push the clips into the groove of the plank.
Step half dozen: Start Attaching Ceiling Planks
Install the planks with staggered seams and continue adding on to the ceiling by connecting the natural language and groove planks.
The residuum of the ceiling will go fairly apace, particularly if you have two people working on information technology!
Depending on the size of your room, you volition have to brand cuts in your planks to stagger them. Mensurate the empty space on each row, mark it with a pencil and cut to size using a saw and install!
Close upwards of a clip within the groove on the plank.
Footstep vii: How to Cutting Planks to Fit Effectually Lite Fixtures
When y'all go to the section of the ceiling where in that location are holes for lite fixtures and or HVAC elements, you will have to cut circles in the planks.
This may seem hard, only with a few tools it is pretty easy.
Brand a Cardboard Template:
First measure the diameter of the hole. Use this measurement and a compass to depict the size circle needed on the cardboard. Cut out with a pair of scissors.
Adhere a plank over the hole and so place the cardboard circumvolve over hole. Trace around the circle with a pencil.
The pencil line is where you need to cut.
Nosotros used a jigsaw to cut the circle out of the plank.
Repeat the process on another plank to fit around the hole. Then continue adding the planks to cover the ceiling.
Cutting Tip: When using whatsoever saw on the planks be conscientious not to get scuff marks on the planks. If the saw leaves any grayness markings employ a damp rag with detergent on information technology to remove them.
Stride 8: Continue Calculation Planks
Prune each plank to the rail, repeating the process until the ceiling is complete. Always leave approximately three/4″ gap from the walls at the ends, which will exist covered past the trim or crown molding.
The final row volition exist just like the get-go row… screwed directly into the metal track (and cut along the length of the plank). Again, be certain to leave 3/iv″ from the border. This gap will be covered with trim or crown molding.
Pace 9: Add Trim or Molding
When installing the crown molding, you will simply exist attaching information technology to the wall not the ceiling. We used finishing nails, a recessed smash punch, and a hammer to adhere the molding around the room.
Two crown molding installation tips if you lot're not a pro:
- If you don't have a miter saw, buy corner blocks where wood is sold at the dwelling house improvement store.
When these blocks are installed in each corner of a room using caulk, no chemical compound miter cuts are needed. Simply flat, straight cuts that you can do with a circular or paw saw.
Once upward, use caulk all around the blocks and molding to make it….
…all look seamless.
Another option for easier crown molding corner cuts:
- If you have a miter saw, brand crown molding corner cutting samples. These will help take the guessing game out of cut corner articulation cuts correctly. This is a crown molding cut tip from Sandra at Sawdust Girl. Her post about crown molding makes the compound cutting process brand sense.
How to Install WoodHaven Ceiling Planks By Yourself
Installing the WoodHaven Ceiling Planks is easier done with two people, but not impossible if you are going to install the ceilings past yourself. This is pretty much what Ed did. I helped with painting and running for tools, and taking photos, but he did most of the work past himself.
When working by yourself, here are some handy installation tips:
- Adhere the border tracks first. Doing this will assistance with making the chalk lines.
Don't screw the screws in all the way around the border tracks around the room. Leave them halfway out until you mark all the ceiling chalk marks.
You can use the screws to attach one stop of the chalk-line as you behave the other end to the opposite side of the room to snap the line.
- Brand spacers out of chip woods. To get in easier to space the tracks evenly across the ceiling, cut flake pieces of forest to the joist spacing measurement. Our joists were 18″ apart.
This made information technology easier for Ed working by himself, so he didn't have to measure every time he added a new track. It as well meant he could concord the new track confronting the two spacers, ensuring the rail was precisely parallel to the previously installed rail.
- Employ two ladders. Information technology volition salve you lots of fourth dimension going up and down. When upward on 1 ladder, you can but reach for what you need when placed on second ladder.
The New Plank Ceiling After Reveal
Later this week I will share a walk-through video of the upstairs of my house and you lot will get to see the ceilings in more than detail.
The new white planks on the ceilings accept changed the vibe of the rooms to more classic and cottage feeling.
No more dusty, dirty looking popcorn.
At present when family and friends stay with us and are lying in bed, they will look upward and see pretty ceilings. :-)
Where to Buy Armstrong WoodHaven Ceiling Planks
Planks are available at your local home improvement store. Click here to run into which Armstrong Ceiling distributors are located in your expanse.
I hope reading how Ed and I did this project and had smashing success inspires you to embrace your popcorn ceilings or if you simply desire to add a archetype bear on to any ceiling in your home.
Source: https://inmyownstyle.com/what-is-the-easiest-way-to-cover-a-popcorn-ceiling.html
0 Response to "what to do with ugly fans in house"
Postar um comentário